TechSoft UK Ltd
 
 
 
<< Back
(All prices shown are in pounds sterling and exclude VAT)
 
  EGX-20 / CAMM 2 PNC-2000/2100/2200 TOOLS
 
 
 
 
 

N.B. Due to the longevity of Roland machinery there are many different models of CAMM 2 still in use in schools. Please check you are ordering the correct tools for your model of CAMM 2.
 
COLLETS
When using more than one tool, the top collet (if left on the cutter) can act as a depth stop. This makes setup very quick and simple. Extra collets are available as follows:
TA-MOD-COLLET
Upper collets to fit 3.17mm tools (pk of 2) 
14.00
 

ENGRAVING TOOLS (40 deg)

engr4011.gif (1730 bytes)

General purpose carbide tipped vee point engraving tools, ground to an included angle of 40 deg. Suitable for engraving most materials, and recommended as a standard tool for all users.

TA-EC3-40 3.17mm x 120mm           
19.00
TA-ECT-REPLACE Replacement re-sharpened TA-EC3-40
(N.B. Tool must be returned to TechSoft)
5.00
 

SLOT DRILLS

sltdrl11.gif (2082 bytes)

General purpose milling/drilling slot drills in solid carbide.  These tools (particularly in sizes 2mm and above) are specially designed to produce a good surface finish on plastic materials such as styrene and acrylic, and non-ferrous metals such as aluminium.  Due to their superior cutting action, they also run quieter than routing cutters.  The drawback is a slightly smaller depth of cut compared to the equivalent router cutter, the flute length being typically 3 to 4 times the diameter. 

TA-SD3-0.8 0.8mm dia 3.17mm x 120mm   
24.00
TA-SD3-1 1mm dia 3.17mm x 120mm   
24.00
TA-SD3-1.5 1.5mm dia 3.17mm x 120mm   
24.00
TA-SD3-2 2mm dia 3.17mm x 120mm   
24.00
TA-SD3-2.5 2.5mm dia 3.17mm x 120mm  
 24.00
TA-SD3-3 3mm dia 3.17mm x 120mm  
24.00
 

BALL NOSED CUTTERS

bllnos11.gif (2041 bytes)

A general purpose round ended cutter in carbide.  It is ideal for 3D modelling, particularly in modelling wax or foam.

TA-BN3-2 2mm dia 3.17mm x 120mm  
27.00
 

PRINTED CIRCUIT BOARD DRILLS

A range of specialist PCB drills in tungsten carbide. 

TA-PD3-0.8 0.8mm dia 3.17mm x 120mm  
18.00
TA-PD3-1 1.0mm dia 3.17mm x 120mm    
18.00
TA-PD3-1.2 1.2mm dia 3.17mm x 120mm      
18.00
TA-PD3-1.5 1.5mm dia 3.17mm x 120mm        
18.00
 

ROUTING CUTTERS - HALF ROUND

hr-cut.gif (1759 bytes)

General purpose tools for milling/drilling/routing in materials such as plastic and wood.  Carbide tipped.  The straight flute does not clear swarf very efficiently, thus care must be taken with deeper cuts.

TA-RC3-50-2 2mm dia 3.17mm x 120mm  
19.00
TA-RC3-50-3 3mm dia 3.17mm x 120mm    
19.00
 

ROUTING CUTTERS - THREE QUARTER ROUND

tqr-cut.gif (1908 bytes)

Similar to the half round cutters, but slightly more inclined to clogging.  However, they are very strong and relatively difficult to break if accidentally overloaded

TA-RC3-75-2 2mm dia 3.17mm x 120mm  
19.00
TA-RC3-75-3 3mm dia 3.17mm x 120mm    
19.00

 
(N.B. All tool lengths are nominal.)